Wednesday, June 8, 2011

How to remove Lower Control Arm on Honda odyssey?

Control Arm Bushing Replacement



The lower control arm bushings are serviced with the lower control arm as an assembly.

Removal & Installation



2001-04 Models
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:

    Front wheel
    Lower ball joint
    Front inner flange bolt
    Rear inner flange bolt
    Lower control arm


To install:


NOTE
Use a new split pin for assembly.

  1. Install or connect the following:

    Lower control arm. Tighten the inner flange bolt (A) to 69 ft. lbs. (93 Nm) and bolt (B) to 90 ft. lbs. (122 Nm) (69 ft. lbs. for 2004 models). Refer to the accompanying illustration for the locations of bolts A and B.
    Lower ball joint. Tighten the nut to 43-51 ft. lbs. (59-69 Nm).
    Front wheel

  2. Check the wheel alignment and adjust as necessary.

    Click image to see an enlarged view

    Fig. Tighten the lower control arm bolts to the specifications-2001-04 models shown


2005-06 Models

Special Tools Required:



Ball joint remover, 32 mm 07MAC-SL0A102
Ball joint thread protector, 14 mm 071AF-S3VA000

  1. Raise the front of the vehicle, and support it with safety stands in the proper locations.
  2. Remove the front wheel.
  3. Remove the flange nut (A) while holding the respective joint pin (B) with a hex wrench (C), then disconnect the stabilizer links from the strut (D).

    Click image to see an enlarged view

    Fig. Remove the flange nut (A) while holding the respective joint pin (B) with a hex wrench (C), then disconnect the stabilizer links from the strut (D)-2005-06 models

  4. Turn the stabilizer bar backward to gain easier access to the front side of the lower arm mounting bolt.
  5. Remove the lock pin from the lower arm ball joint castle nut, and remove the nut.

    Click image to see an enlarged view

    Fig. Remove the lock pin from the lower arm ball joint castle nut, and remove the nut-2005-06 models

  6. Remove the lower ball joint from the knuckle using the special tools.
  7. Remove the flange bolts (A), then remove the lower arm (B).

    Click image to see an enlarged view

    Fig. Remove the flange bolts (A), then remove the lower arm (B)-2005-06 models

  8. Install the lower arm in the reverse order of removal, and note these items:

    Be careful not to damage the ball joint boot when connecting the lower arm to the knuckle.
    Place a jack under the lower arm, and raise the lower arm to load the suspension with the vehicle's weight.
    Tighten all mounting hardware to the specified torque values.
    Torque the castle nut to the lower torque specification, then tighten it only far enough to align the slot with the hole in the stud. Do not align the castle nut by loosening it.
    Use a new lock pin on the castle nut.
    Connect the struts to the links.
    Before installing the wheel, clean the mating surface on the brake disc and the inside of the wheel.
    Check the front wheel alignment, and adjust it if necessary.




    To Order car parts online:--To get heavy discount on car parts .Click this link below:----

    http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

    For car error code diagnosis click the link below:---

    http://www.automd.com/diagnose/?amdcid=apwldrbrd1

    Car no start:--

    http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

No comments:

Post a Comment